Заголовок статьи | «Инфология процессов функционирования гибких производственных систем» |
Авторы | А.И. Сердюк, А.Б. Радыгин, В.Н. Шерстобитова |
Аннотация | Приводится математическое и алгоритмическое описание процессов функционирования ГПС, предназначенное для разработки компьютерных приложений, используемых при проектировании высокоавтоматизированных производственных систем с заданными свойствами. Описываются математические модели общесистемных показателей эффективности, рассчитываемых на основании внутрицикловых составляющих работы системы и потерь по различным причинам. |
Ключевые слова | машиностроение, гибкая автоматизация, гибкие производственные системы, компьютерное моделирование, анализ, синтез |
УДК | 65.011.56 |
Выпуск | «Проблемы машиностроения и автоматизации» №4 за 2016 год |
Сведения об авторах
Сердюк Анатолий Иванович — д-р техн. наук, профессор, директор Аэрокосмического института Оренбургского государственного университета,
Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.
, Победы проспект, д. 13, Оренбург, 460018, Россия
Радыгин Алексей Борисович — зам. генерального директора по техническому перевооружению и перспективному развитию АО «ПО «Стрела»,
+7 (3532) 75 71 00,
Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.
, Шевченко ул., д. 26, Оренбург, 460005, Россия
Шерстобитова Вероника Николаевна — канд. техн. наук, доцент, доцент кафедры систем автоматизации производства Оренбургского государственного университета,
Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.
, Победы проспект, д. 13, Оренбург, 460018, Россия
Article title | «Infologiya of functioning processes of flexible manufacturing systems» |
Authors | A.I. Serdуuk, A.B. Radygin, V.N. Sherstobitova |
Abstract | The contents of processes of functioning FMS are considered in the form of deterministic representation of the logic of interaction and content basic cycles of working of technological and service modules, their components and assemblies, up to the cycles of training and changing of cutting tools in the cutting zone. The design scheme to mathematical models of cyclic components and shape visualization of processes of functioning FMS are presented in the auto-generated cyclograms. The set of input data necessary and sufficient for automated generation of cyclograms are identified. The mathematical models of a system-wide indexes of effectivenes that are calculated on the basis of inside cycles of the components of system work and losses for difference reasons are described. Developed mathematical and algorithmical description of processing functioning FMS is intended for creation computer application used as problem-oriented tools modeling and assessment of the effectiveness for specialists of different profiles working at a single project to create highly automated production systems with desired properties. |
Keywords | engineering, flexible automation, flexible manufacturing systems, computer simulation, analysis, synthesis |
UDC | 65.011.56 |
Issue | «ENGINEERING AND AUTOMATION PROBLEMS» №4, 2016 |
Information about authors
Serdуuk Anatoliy Ivanovich — DSc, Professor, Director of Aerospace Institute, Orenburg State University,
Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.
, 13, Pobedy Avenue, Orenburg, 460018, Russia
Radygin Aleksey Borisovich — Deputy Director General on Technical Re-Equipment and Development SS «PA «Strela»,
Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.
, 26, Shevchenko Str., Orenburg, 460005, Russia
Sherstobitova Veronika Nikolaevna — PhD, Associate Professor, Associate Professor of Department of Automation of Production, Orenburg State University,
Данный адрес e-mail защищен от спам-ботов, Вам необходимо включить Javascript для его просмотра.
, 13, Pobedy Avenue, Orenburg, 460018, Russia